Communicate with Supplier? Supplier
Wini Zhou Ms. Wini Zhou
What can I do for you?
Chat Now Contact Supplier
About Us

Company Name: WENZHOU WINIBER MACHINERY EQUIPMENT CO., LTD.

Business Type: Manufacturer , Trade Company

Main Products: PET Blowing Machine , PET Preform Mould , Bottle Blowing Machine , Filling Machine , Bottle Production Line , Water Production Line

Export Percentage: 91% - 100%

Year Established: 2011

NEWS
The bottled mineral water filling machine is a self-priming filling of the leather tube, and the leather tube is placed in the material storage barrel. Under the action of the cylinder pulling the piston rod, the material enters the metering cylinder through the self-suction tube and the three-way lower check valve, and then The piston pushes the piston to push the material out, and the material enters the container through the three-way upper check valve, the leather tube and the filling head, and the amount of the filling is determined by the magnetic control switch controlling the stroke of the cylinder. Installation and commissioning of bottled mineral water filling machine 1. Install and then debug, read the instructions carefully before commissioning, and prepare the tools used. 2. After the installation, brushing machine and the rinsing machine are installed, the filling track and the bottle receiving tray are leveled, the liquid storage tank is filled with materials, and all the electrical switches are in the closed position. 3. Fill the container into the tool box, connect the external power supply, the power socket must be a three-pin socket, and have a reliable grounding wire to prevent the chassis from leaking power, turn the machine power switch to ON, and the power indicator light. 4. The mounting support plate holds the filling frame and points to the positioning sleeve on the top filling head. The positioning sleeve should be able to move up and down flexibly, and the filling needle is exposed or retracted without hindrance. 5. The switch under the liquid storage tank is turned to the open position, so that the material can flow into the total metering pump. According to the total filling amount of each container, adjust the screw on the crank and rotate the knob of the filling speed control board to 20 degrees. Left and right, then turn the switch on the filling speed control board to the open position. 6. When the filling head out of the liquid is the set amount, screw the liquid amount fine-tuning nut, cover the filling head housing, and loosen the filling bracket support plate.

2020-08-31

Here we introduce some points to help customers to operate bottle blowing machine safely. 1. Before each shift, blowing part each unit must be lubricated once. (manipulator, manipulator guide, open and close mold guide) 2. The swing arm can be added once (3 - 4) days. Heating machine large chain, small chain can be once a month. Check the main engine reducer and heating machine reducer for lack of oil. The main bearing can be added once every two to three months. 3 . Before production, check if the moving parts are fixed and whether the screws loosen and fall off, especially if the impact force is strong, and whether the belt drive part is abnormal. 4 . Check whether high and low pressure gas source, power source and water source are normal. 5. Check each emergency stop switch, safety door switch, protective device detection switch is normal. 6 . Check the warming head into the embryo, if the embryos are working properly. Insert the embryo if not in place to adjust the embossing device nut. 7. Check the lamp for damage and break. Replace it in time. 8 . Check whether each pneumatic component leaks and the action is sensitive. 9. Whether the triplex is abnormally leaky, whether it is blocked, and whether the water in the cup is too full. 10. If there is an abnormality in the solenoid valve of the blowing machine, it must be cleaned in a timely manner. 11. When the high and low pressure gas source switch is turned on, it must be operated slowly to prevent the gas source from flowing too fast. The dirt can be blown into the solenoid valve and the exhaust valve can be opened for 30 seconds to ensure the air is clean. 12. When starting the machine, it must be convinced that the mechanical part is good and that no one inside the machine has any foreign objects. Especially shake the position to avoid hurting people. At the same time, close the security door. 13. When starting the machine, the motor must be started and the heating machine must be delayed for 30 seconds to prevent voltage fluctuations. Before starting warming, make sure that the cooling water is not turned on. 14. After warming start (2-3) minutes, wait until the oven temperature rises evenly and press the embryo button. At the same time, the bottle blowing power must also be turned on, otherwise it will not blow the bottle. 15. When the machine is in operation, it must pay close attention to whether the machine has abnormal noise. 16. In the event of an emergency, the emergency stop button may be pressed for emergency braking. Then analyze the cause of the formation according to the site conditions and find a quick solution to the problem. 17. After normal operation of the machine, do not put any part of the body into the machine to avoid injury to the robot. If the machine has abnormal noise, it can be observed after deceleration. 18. After the machine is normally produced, the operator must observe the quality of the bottle from time to time in order to avoid fluctuations in the voltage or other factors affecting the blowing quality. 19. When the blowing machine is repaired, press the touch screen fault repair button to ensure safe maintenance. If you need to manually observe the action of each individual cavity, please pay attention to the position of the robot. At the same time, be sure to clear the role of individual buttons, and then move. Make sure that malfunctions cause unnecessary trouble. 20. After each maintenance of the machine, it is necessary to clean things such as tools and screws so as not to remain in the machine and affect the normal operation of the machine.

2020-06-27

Because of coronavirus crisis, our PET bottle blowing machine is more popular in this year. The PET Bottle mainly used for sanitizer, antibacterial gel and so on. One of our customer who strated the bottle business in 2018. He purchased the PET injection machine, PET preform mould, Bottle Mould and PET blowing machine to make his own bottles. I receive his message today that his company in newpaper. The reason is government thanks for their helping hospital in coronavirus ciris. Also he told us: your help is essential also that's why I am very grateful with you and all you do for me. I am so pround of him and his company. Winiber always do everything best for customer. Will go with customer along.

2020-03-25

Flexible and efficient blow molding machine The AL series is the latest fully-automated blow molding machine in our company. The AL-7 has a productivity of 12000 bottles/hr and the AL-8 has a productivity of 14000 bottles/hr. Hours, apply 0.1-1.5 liter containers. The AL series uses a straight-line structure that is simple and reliable, combined with perfect PET processing technology to make the machine more flexible and reliable. The machine adopts a digitally controlled heating unit, which makes the setting of various preform temperatures more accurate and makes the material distribution of preforms during processing more reasonable, thus ensuring the quality of the bottles and reducing the weight of the bottles. The blowing molding machine has the technical advantages Machine reliability The structure is compact and reasonable, and the device is protected by electrical and mechanical safety systems. It has a long life and only a few consumables. Constant productivity, built on unique structural design. Automatic operation The main control unit uses Simens products. Various operating functions are all controlled by the control panel. Each production parameter is stored in the machine, which can be recorded and printed for inspection and modification by the operator to improve product quality. Bottle weight reduction Thanks to the precise digital temperature control system and complete stretching movement, the material distribution is optimized. Winiber company is dedicated focusing on PET blowing machine, PET Preform mould and water filling machines.

2020-03-13

Happy new year to global customers and their families. We would like to wish u and your families a very prosperous new year in 2020. May your new yer is filled with peace and joy! In 2019, Winiber insisted on offering customer high quality PET preform mould, PET blowing machine and water filling line with excellent service. In 2020, we will continue to work more hard to the further development!

2020-01-10

Our company develop a new type PET bottle blowing machine. This design between semi-automatic and automatic. Preoform comes into preheater automatically and the bottle drop automatically. Worker only take the preforms from the heater to blower. The output is improved greatly. Normal working can be 2500BPH. This type PET bottle blowing machine is a better choice to instead of traditional semi-automatic blowing machine to save the labor cost!

2019-12-27

Contact Us
Wini ZhouMs. Wini Zhou

Ms. Wini Zhou

wini@winiber.com

  • Tel:86-0577-83531938
  • Mobile Phone:+8615857698681Contact me with Whatsapp
  • Email: wini@winiber.com
  • Address:HIGH-TECH BUSINESS INCUBATOR, XINYE ROAD, BINHAI NEW DISTRICT, PINGYANG, WENZHOU, ZHEJIANG, CHINA, Wenzhou, Zhejiang
  • Wechat: 008615857698681
  • Bossgoo Showroom:http://winiber.bossgoo.com
Related Products List